•  

    3" Engraving Block Ball Vise Setting Jewelry w/ Pins Rubber Base

    $79.00 USD
    • US shipping only

    • Diameter : 3"
    • Heavy Steel Body
    • 360° Tilt, Spin and Rotate Movement
    • Nylon Vise
    • Vise Jaw Opening:: 1-1/2”
    • 24 Pin Hole Slots
    • 12pc 25/32” x 5/32” Dia Pins:
    - 6 Round Head Pins
    - 6 Flat Head Pins
    • 13/32” Hex Nut Wrench Key
    - Locks 360° Spin
    - Controls Jaw
    • Rubber Base
    • Weight: 5.1 lbs
    • Box Pack

  •  

    WHALEY SLIDING HAMMER

    $50.00 USD

    ATTENTION METALSMITHS… Need to move metal in a very careful and precise way? Now it’s easier with the NEW Whaley Sliding Hammer. This revolutionary tool has a slender, hollow hammer head which holds a long punch that slides back and forth within the hammer head. Great for stone setting, channel setting, riveting, repoussé, texturing, chasing and more.

        Patent Pending.
        Punch stays aligned within the hammer body which means each hammer strike is perfectly aligned for the next blow. No more guess work!
        Hammer force whether it’s gentle or extremely forceful can be felt and controlled by the hand.
        Can be used in any position-punches rotate and head swivels with ease.
        Comes with 3 hardened stainless steel punches.
        Handle made of finished rosewood. 

  •  

    MILGRAIN TOOL

    $11.00 USD

    Premium European-made millgrain tools are used for forming decorative edges on settings and bezels. 

  •  

    MILGRAIN TOOL SET (6 PC & HANDLE

    $65.00 USD

    Premium European-made millgrain tools are used for forming decorative edges on settings and bezels. Set of six assorted sizes, ranging from 2-12 with premium chuck style handle.

  •  

    Riveting Block

    $39.00 USD

    With our new Steel Riveting Block, there is no more guesswork on the length of wire to be cut. Use the holes at the top to pre-cut the perfect length of wire for your projects. The holes in the middle are about 1.8mm deep, thus every cut is just the right amount of wire needed to create "head" on both sides. The dimples on the left side are used for support when riveting in order to hold the shape of the rounded rivet head. The circles on the right side are for riveting eyelets in 3 different sizes without flattening the rounded rims. Dimples on the side of the block are for rivets and on the opposite side are circles for eyelets. Both of these sides are for CURVED surfaces and must be mounted in a vise.

  •  

    16pc Ring Stretcher Set

    $59.00 USD

    Stretches rings with mountings without loosening prongs or stressing stone settings when other stretchers cannot be used. Also can be used on bands. Supplied with with curved groove and angled groove rollers to accommodate all ring sizes. Easy to use. Replacement roller set also available.

     

    • Dimensions:7- 1/4” x 3 -5/8” x 3- 1/4”
    • 16pc Rollers :
    - 10pc “V” Grooves
    - 6pc “U” Grooves
    • Stainless Steel Rollers
    • Plastic Case for Rollers

     

     

  •  

    DELUXE 4 HOLE METAL PUNCH

    $59.00 USD

    Create holes for wire rivets in 18, 16, 14 and 12 gauge. Punch holes up to 18 gauge metal sheets or multiple metal sheets together with ease.

  •  

    BENCHTOP DRILL PRESS-

    $89.00 USD

    Small and compact describes this new drill press from EURO TOOL. The base measures 6.75 x 6.75 with a drill clearance of 5 inches. This drill has three settings that allow for a range of 0-8500 RPM. When space is an issue, this drill press will perform with ease. The Jacobs chuck accepts bits up to 6.5mm. Canada safety approved.

  •  

    Martini setting holder

    $21.00 USD

    Made exclusively by EURO TOOL to hold three prong “Martini” mountings. Each die adapts to the accompanying pin vise. The pin vise holds the mounting in place so that the jeweler can close each prong with a pair of pliers. Set comes complete with pin vise.

  •  

    MAGNETIC FLEXIBLE LIGHT

    $25.00 USD

    The Versa-Light is a super bright LED light with three settings: High Beam, Low Beam and Flash. The sturdy clip holds the light while the 8-1/2 inch flexible arm allows for easy adjustment. The strong magnetic base stays secure on metal surfaces for hands free work. Use the light zoom function to pinpoint light onto small areas or zoom out for a wider view. Includes 3 AAA batteries.

  •  

    Ring Stretcher and Reducer Top Quality

    $179.00 USD
    • Free US Shipping

    EURO TOOL's Ring Stretcher/Reducer is great quality and a great value! Enlarges and reduces rings quickly. Mandrel clearly marked with ring sizes 1-15. Tapered mandrel has 6 splines. Reduction plate is two-sided with 16 reduction depressions. Four holes in base for mounting on sturdy workbench or table. Overall height: 16". Complete instructions included.

  •  

    200 PC.DRILL SET IN WOOD STAND 61-80

    $100.00 USD

    Quality made HSS twist drills made to exacting tolerances. Bright finished, with exactly the proper cutting angle at the tip. Flutes are sharp with the proper spiral and finished outer edges. The finest grade tool steel, tempered for maximum hardness and endurance. Assortment includes one tube (10 pc) each sizes 61-80 and a hardwood stand marked with the appropriate size. 

  •  

    360 MANDREL VISE W/ MANDREL

    $36.00 USD

    Introducing the 360° Mandrel Vise. Unique ball and socket provides 360° swivel/pivot as well as horizontal position with a locking mechanism to hold firmly at any angle. Great for wireworking. Simply Screw on our MAN-255.00 and work hands free. This solves the problem of working with the mandrel when both hands are needed. The vise may be clamped to most benches or table tops with an opening up to 2-1/8". This vise works exclusively with MAN-255.00, MAN-260.00, MAN-262.00, and MAN-264.00 - all from EURO TOOL. Not meant for heavy hammering. A EURO TOOL Exclusive!

  •  

    Disc Cutter

    $55.00 USD

    Sweet Disc Cutter set for you fabricators and metal smiths $55 plus shipping

    • Dimensions: 4 -1/8” x 1- 3/4” x 1- 1/8”
    • Cut Disc Sizes: 7/64”, 11/64”, 15/64”, 3/16”, 17/64”, 19/64”, 5/16”, 21/64”, 25/64”, 7/16”, 15/32”, 1/2”, 35/64”, 5/8”
    • Stainless Steel
    • Box

  •  

    Dapping Set

    $40.00 USD

     This set includes 12 steel dapping punches ranging from 2-13 mm in diameter; a dapping block flat with 12 depressions ranging from 2-13 mm in diameter; and a hardwood stand to hold all the pieces.

    • Punch sizes in mm: 2,3,4,5, 6, 7, 8, 9, 10, 11, 12, 13
    • The dapping block is made of polished tool hardened steel and measures 1-7/8" x 1-7/8" x 1/2"
    • Hardness: 45-50HRC
    • Wooden block (Dim: 35 x 195 x 115mm) is etched with measurement labels for each punch in millimeters.

  •  

    Bench Block

    $25.00 USD

    This three piece set includes a thick vulcanized firm rubber base which absorbs shock, plus a solid steel block which is 15/16" (24mm) thick and 3" (75mm) in diameter. The third piece is a sturdy nylon block the same size that fits into the rubber base for lighter, more delicate work. This is a well made set, and allows one to hammer without creating excess noise and vibration at the bench. 2.5 lbs. 50-55 HRC

  •  

    Bench Top fume Extractor

    $59.00 USD

    Lead-free solder has created a healthier environment, but the more active fluxes required to be used, the more fumes are produced. Our new Fume Extractor is the perfect solution to this smoky problem. Features: Remove flux fumes from soldering workbench by drawing smoke through carbon-activated filter. Can process up to 1.37 cubic meters of air per minute. Adjustable stand allows for various angles. Quiet fan. ESD safe. Comes with two filters.

  •  

    Bench Pin and Anvil

    $45.00 USD

    I just ordered a bunch of these. Real nice quality. Great for someone that is starting out and doesn't have a bench yet. Mandrels not included. I sure wish these were available years ago. Price is $45 plus shipping.

    Clamp-on bench anvil with bench pin is portable and versatile for hammering, sawing, filing and flattening. Securely attach your wooden pin, ring Mandrel, or Bracelet Mandrel to the handy clamp-on bench anvil mounting system enabling you to work faster and smarter. Our bench anvil can clamp-on to a bench or Table allowing you to hammer, flatten, or saw on the 4-1/2" x 2-7/8" Flat anvil surface or for finishing work on jewelry mount a hardwood bench pin, ring or Bracelet Mandrel into the anvil bench pin or round openings. Clamp-on bench anvil is used for hammering, sawing, filing and flattening anvil securely attaches to bench or Table.

    • Overall dimensions: 5-1/4" x 4-1/2" x 2-7/8"
    • Bench mounting system which has a 4-1/2" x 2-7/8" flat anvil surface on top
    • Anvil opening for bench pin: 2-1/4" x 9/16"
    • Wooden bench pin dimensions: 7-1/2" L x 2" w x 1/2"
    • Pin round hole diameter: 3/4"
    • V-Slot opening: 1"
    • Anvil weight: 5 lbs
    • Clamp-on anvil securely attaches to bench or table
    • A portable, versatile device for Hammering, sawing, filing and flattening
    • Durable hardwood V slot bench pin with saw groove

  •  

    Bezel Pushing Set

    $60.00 USD

    Pick your choice of the 2 sets

     

    • 18 Pcs Set Prong Closing Punch Set
    • Punch Sizes:
    - 0.75mm
    - 1mm, 1.25mm , 1.5mm, 1.75mm
    - 2mm, 2.25mm,  2.50mm, 2.75mm
    - 3mm, 3.25mm, 3.5mm
    - 4mm, 4.5mm,
    - 5mm, 5.5mm
    - 6.5mm
    - 7.5mm

     

    • 16 Pcs Set Prong Closing Punch Set
    • Sizes
      - 2mm, 2.75mm
      - 3.75mm
      - 4.5mm
      - 5mm, 5.25mm, 5.5mm
      - 6mm, 6.5mm
      - 7mm, 7.5mm
      - 8mm, 8.5mm
      - 9mm
    • Comes in a Wooden Storage Box

  •  

    Universal Parts Holder

    $17.00 USD

    • Dimensions: 5-1/2” x 2” Dia.
    • Jaw Opens: 3/4”
    • 60 Cavities and 8 Pins
    • Aluminum Body
    • Wooden Handle
    • 2 Wood Mounting Screws
    • Used for repairing and engraving Jewelry,  for Bending & forming wire

  •  

    6-3/4" Cross Action Bent Tip Fiber Grip Tweezer with Stand

    $24.00 USD
    • PRICE IS FOR 6 TWEEZERS

    • Length: 6-3/4”
    • Cross Action
    • Fiber Grip

  •  

    9 in 1, 8 oz Texturing Hammer, Interchangeable Heads, 9-1/2" Length

    $20.00 USD

    • 9 Interchangeable Faces:
    - Stripe
    - Rounded Stripe (Rain)
    - Square (Checker Board)
    - Cross (Diamond)
    - Dome (Moon Face )
    - Dimple
    - Single Cone
    - Single Round
    - Single Square

    • Overall Length: 9-1/2”
    • Face Diameters: 3/4”
    • Wood Handle

  •  

    Stainless Steel Grooved & Laser Marked Ring Mandrel

    $25.00 USD

    • Length: 13"
    • Size 1-16
    • Stainless Steel
    • Grooved
    • Laser Marked

 

[ Previous Page / 1 / Next Page ]

  • 3" Engraving Block Ball Vise Setting Jewelry w/ Pins Rubber Base

    $79.00 USD
    • US shipping only

    • Diameter : 3"
    • Heavy Steel Body
    • 360° Tilt, Spin and Rotate Movement
    • Nylon Vise
    • Vise Jaw Opening:: 1-1/2”
    • 24 Pin Hole Slots
    • 12pc 25/32” x 5/32” Dia Pins:
    - 6 Round Head Pins
    - 6 Flat Head Pins
    • 13/32” Hex Nut Wrench Key
    - Locks 360° Spin
    - Controls Jaw
    • Rubber Base
    • Weight: 5.1 lbs
    • Box Pack

  • WHALEY SLIDING HAMMER

    $50.00 USD

    ATTENTION METALSMITHS… Need to move metal in a very careful and precise way? Now it’s easier with the NEW Whaley Sliding Hammer. This revolutionary tool has a slender, hollow hammer head which holds a long punch that slides back and forth within the hammer head. Great for stone setting, channel setting, riveting, repoussé, texturing, chasing and more.

        Patent Pending.
        Punch stays aligned within the hammer body which means each hammer strike is perfectly aligned for the next blow. No more guess work!
        Hammer force whether it’s gentle or extremely forceful can be felt and controlled by the hand.
        Can be used in any position-punches rotate and head swivels with ease.
        Comes with 3 hardened stainless steel punches.
        Handle made of finished rosewood. 

  • MILGRAIN TOOL

    $11.00 USD

    Premium European-made millgrain tools are used for forming decorative edges on settings and bezels. 

  • MILGRAIN TOOL SET (6 PC & HANDLE

    $65.00 USD

    Premium European-made millgrain tools are used for forming decorative edges on settings and bezels. Set of six assorted sizes, ranging from 2-12 with premium chuck style handle.

  • Riveting Block

    $39.00 USD

    With our new Steel Riveting Block, there is no more guesswork on the length of wire to be cut. Use the holes at the top to pre-cut the perfect length of wire for your projects. The holes in the middle are about 1.8mm deep, thus every cut is just the right amount of wire needed to create "head" on both sides. The dimples on the left side are used for support when riveting in order to hold the shape of the rounded rivet head. The circles on the right side are for riveting eyelets in 3 different sizes without flattening the rounded rims. Dimples on the side of the block are for rivets and on the opposite side are circles for eyelets. Both of these sides are for CURVED surfaces and must be mounted in a vise.

  • 16pc Ring Stretcher Set

    $59.00 USD

    Stretches rings with mountings without loosening prongs or stressing stone settings when other stretchers cannot be used. Also can be used on bands. Supplied with with curved groove and angled groove rollers to accommodate all ring sizes. Easy to use. Replacement roller set also available.

     

    • Dimensions:7- 1/4” x 3 -5/8” x 3- 1/4”
    • 16pc Rollers :
    - 10pc “V” Grooves
    - 6pc “U” Grooves
    • Stainless Steel Rollers
    • Plastic Case for Rollers

     

     

  • DELUXE 4 HOLE METAL PUNCH

    $59.00 USD

    Create holes for wire rivets in 18, 16, 14 and 12 gauge. Punch holes up to 18 gauge metal sheets or multiple metal sheets together with ease.

  • BENCHTOP DRILL PRESS-

    $89.00 USD

    Small and compact describes this new drill press from EURO TOOL. The base measures 6.75 x 6.75 with a drill clearance of 5 inches. This drill has three settings that allow for a range of 0-8500 RPM. When space is an issue, this drill press will perform with ease. The Jacobs chuck accepts bits up to 6.5mm. Canada safety approved.

  • Martini setting holder

    $21.00 USD

    Made exclusively by EURO TOOL to hold three prong “Martini” mountings. Each die adapts to the accompanying pin vise. The pin vise holds the mounting in place so that the jeweler can close each prong with a pair of pliers. Set comes complete with pin vise.

  • MAGNETIC FLEXIBLE LIGHT

    $25.00 USD

    The Versa-Light is a super bright LED light with three settings: High Beam, Low Beam and Flash. The sturdy clip holds the light while the 8-1/2 inch flexible arm allows for easy adjustment. The strong magnetic base stays secure on metal surfaces for hands free work. Use the light zoom function to pinpoint light onto small areas or zoom out for a wider view. Includes 3 AAA batteries.

  • Ring Stretcher and Reducer Top Quality

    $179.00 USD
    • Free US Shipping

    EURO TOOL's Ring Stretcher/Reducer is great quality and a great value! Enlarges and reduces rings quickly. Mandrel clearly marked with ring sizes 1-15. Tapered mandrel has 6 splines. Reduction plate is two-sided with 16 reduction depressions. Four holes in base for mounting on sturdy workbench or table. Overall height: 16". Complete instructions included.

  • 200 PC.DRILL SET IN WOOD STAND 61-80

    $100.00 USD

    Quality made HSS twist drills made to exacting tolerances. Bright finished, with exactly the proper cutting angle at the tip. Flutes are sharp with the proper spiral and finished outer edges. The finest grade tool steel, tempered for maximum hardness and endurance. Assortment includes one tube (10 pc) each sizes 61-80 and a hardwood stand marked with the appropriate size. 

  • 360 MANDREL VISE W/ MANDREL

    $36.00 USD

    Introducing the 360° Mandrel Vise. Unique ball and socket provides 360° swivel/pivot as well as horizontal position with a locking mechanism to hold firmly at any angle. Great for wireworking. Simply Screw on our MAN-255.00 and work hands free. This solves the problem of working with the mandrel when both hands are needed. The vise may be clamped to most benches or table tops with an opening up to 2-1/8". This vise works exclusively with MAN-255.00, MAN-260.00, MAN-262.00, and MAN-264.00 - all from EURO TOOL. Not meant for heavy hammering. A EURO TOOL Exclusive!

  • Disc Cutter

    $55.00 USD

    Sweet Disc Cutter set for you fabricators and metal smiths $55 plus shipping

    • Dimensions: 4 -1/8” x 1- 3/4” x 1- 1/8”
    • Cut Disc Sizes: 7/64”, 11/64”, 15/64”, 3/16”, 17/64”, 19/64”, 5/16”, 21/64”, 25/64”, 7/16”, 15/32”, 1/2”, 35/64”, 5/8”
    • Stainless Steel
    • Box

  • Dapping Set

    $40.00 USD

     This set includes 12 steel dapping punches ranging from 2-13 mm in diameter; a dapping block flat with 12 depressions ranging from 2-13 mm in diameter; and a hardwood stand to hold all the pieces.

    • Punch sizes in mm: 2,3,4,5, 6, 7, 8, 9, 10, 11, 12, 13
    • The dapping block is made of polished tool hardened steel and measures 1-7/8" x 1-7/8" x 1/2"
    • Hardness: 45-50HRC
    • Wooden block (Dim: 35 x 195 x 115mm) is etched with measurement labels for each punch in millimeters.

  • Bench Block

    $25.00 USD

    This three piece set includes a thick vulcanized firm rubber base which absorbs shock, plus a solid steel block which is 15/16" (24mm) thick and 3" (75mm) in diameter. The third piece is a sturdy nylon block the same size that fits into the rubber base for lighter, more delicate work. This is a well made set, and allows one to hammer without creating excess noise and vibration at the bench. 2.5 lbs. 50-55 HRC

  • Bench Top fume Extractor

    $59.00 USD

    Lead-free solder has created a healthier environment, but the more active fluxes required to be used, the more fumes are produced. Our new Fume Extractor is the perfect solution to this smoky problem. Features: Remove flux fumes from soldering workbench by drawing smoke through carbon-activated filter. Can process up to 1.37 cubic meters of air per minute. Adjustable stand allows for various angles. Quiet fan. ESD safe. Comes with two filters.

  • Bench Pin and Anvil

    $45.00 USD

    I just ordered a bunch of these. Real nice quality. Great for someone that is starting out and doesn't have a bench yet. Mandrels not included. I sure wish these were available years ago. Price is $45 plus shipping.

    Clamp-on bench anvil with bench pin is portable and versatile for hammering, sawing, filing and flattening. Securely attach your wooden pin, ring Mandrel, or Bracelet Mandrel to the handy clamp-on bench anvil mounting system enabling you to work faster and smarter. Our bench anvil can clamp-on to a bench or Table allowing you to hammer, flatten, or saw on the 4-1/2" x 2-7/8" Flat anvil surface or for finishing work on jewelry mount a hardwood bench pin, ring or Bracelet Mandrel into the anvil bench pin or round openings. Clamp-on bench anvil is used for hammering, sawing, filing and flattening anvil securely attaches to bench or Table.

    • Overall dimensions: 5-1/4" x 4-1/2" x 2-7/8"
    • Bench mounting system which has a 4-1/2" x 2-7/8" flat anvil surface on top
    • Anvil opening for bench pin: 2-1/4" x 9/16"
    • Wooden bench pin dimensions: 7-1/2" L x 2" w x 1/2"
    • Pin round hole diameter: 3/4"
    • V-Slot opening: 1"
    • Anvil weight: 5 lbs
    • Clamp-on anvil securely attaches to bench or table
    • A portable, versatile device for Hammering, sawing, filing and flattening
    • Durable hardwood V slot bench pin with saw groove

  • Bezel Pushing Set

    $60.00 USD

    Pick your choice of the 2 sets

     

    • 18 Pcs Set Prong Closing Punch Set
    • Punch Sizes:
    - 0.75mm
    - 1mm, 1.25mm , 1.5mm, 1.75mm
    - 2mm, 2.25mm,  2.50mm, 2.75mm
    - 3mm, 3.25mm, 3.5mm
    - 4mm, 4.5mm,
    - 5mm, 5.5mm
    - 6.5mm
    - 7.5mm

     

    • 16 Pcs Set Prong Closing Punch Set
    • Sizes
      - 2mm, 2.75mm
      - 3.75mm
      - 4.5mm
      - 5mm, 5.25mm, 5.5mm
      - 6mm, 6.5mm
      - 7mm, 7.5mm
      - 8mm, 8.5mm
      - 9mm
    • Comes in a Wooden Storage Box

  • Universal Parts Holder

    $17.00 USD

    • Dimensions: 5-1/2” x 2” Dia.
    • Jaw Opens: 3/4”
    • 60 Cavities and 8 Pins
    • Aluminum Body
    • Wooden Handle
    • 2 Wood Mounting Screws
    • Used for repairing and engraving Jewelry,  for Bending & forming wire

  • 6-3/4" Cross Action Bent Tip Fiber Grip Tweezer with Stand

    $24.00 USD
    • PRICE IS FOR 6 TWEEZERS

    • Length: 6-3/4”
    • Cross Action
    • Fiber Grip

  • 9 in 1, 8 oz Texturing Hammer, Interchangeable Heads, 9-1/2" Length

    $20.00 USD

    • 9 Interchangeable Faces:
    - Stripe
    - Rounded Stripe (Rain)
    - Square (Checker Board)
    - Cross (Diamond)
    - Dome (Moon Face )
    - Dimple
    - Single Cone
    - Single Round
    - Single Square

    • Overall Length: 9-1/2”
    • Face Diameters: 3/4”
    • Wood Handle

  • Stainless Steel Grooved & Laser Marked Ring Mandrel

    $25.00 USD

    • Length: 13"
    • Size 1-16
    • Stainless Steel
    • Grooved
    • Laser Marked

 

[ Previous Page / 1 / Next Page ]

This website is created and hosted by Website.com's Site Builder.